Explicit dynamics with OpenRadioss

morphogen.dynamics simulates the crushing, tension, shear and impact of a morphology at the rates of crashes, shocks and drops with OpenRadioss, the open-source explicit finite element solver (AGPL-3.0; run as a separate program, installed from its releases by morphogen radioss install, see Installation): its voxels as stabilized 8-node bricks or a conforming mesh of its level set as tetrahedra, its phases elastic, von Mises elastoplastic (the linear, Voce and Norton hardenings of morphoGen tabulated in LAW36) or Johnson–Cook (LAW2), with failure by element deletion, the self contact of its folding struts and closing cells (TYPE24), its faces held and driven after a smooth start, or the whole thrown against a rigid wall; its nominal stress–strain curves at both faces (their gap telling a quasi-static test from a dynamic one), energies, peak and plateau stresses, densification strain, absorbed energy per volume and mass, and its fields over time (morphogen radioss export|run|read, the tab Explicit dynamics). The inputs are the Radioss Block Format of the reference guide, written with their manifest so that a run made elsewhere (a cluster) is read back.

import morphogen as mg
from morphogen import dynamics

lattice = mg.model_from_config(
    {"type": "tpms", "surface": "gyroid", "volume_fraction": 0.2, "cell_size": 5.0}
)  # an aluminium gyroid, its lengths in mm
micro = lattice.generate(mg.Domain.cube(10.0), seed=1)
materials = {
    0: "void",
    1: {
        "young": 70e3,  # MPa
        "poisson": 0.33,
        "density": 2.7e-9,  # Mg/mm³
        "plasticity": {"yield": 150.0, "hardening": 600.0},
        "failure_strain": 0.4,
    },
}
test = dynamics.explicit_test(
    micro,
    materials,
    {"kind": "compression", "strain": 0.6, "strain_rate": 500.0},
    "gyroid_crush",
    resolution=32,
)  # units: Mg, mm, s by default
values = dynamics.summary(test.result)  # peak and plateau stresses (MPa), densification...

The loadings are compression, tension and shear (the lower face held, the upper one driven at the nominal strain rate after a smooth start, laterally fixed or free) and impact (the morphology thrown at a velocity against a rigid wall), with the self contact of the outer surface by default. The values are in the consistent unit system of units (dynamics.UnitSystem: Mg, mm, s by default, i.e. MPa, Mg/mm³, mm/s, N, mJ; length_scale converts the lengths of the morphology). The time step of an explicit run is that of the smallest element (dynamics.critical_time_step; the manifest of the inputs gives the number of cycles before the run): a coarser mesh, a higher rate or a minimum time step (time_step, mass scaling) shortens it. The command line does the same from a geometry or an image, and reads back a run made elsewhere:

morphogen radioss install                       # the latest release, from GitHub
morphogen radioss export gyroid.json --materials aluminium.yaml --voxels 32 \
    --loading compression --strain 0.6 --rate 500 -o crush
morphogen radioss run crush --threads 8         # Starter, Engine, conversions, summary
morphogen radioss read crush --frames-vtu       # curves.csv, energies.csv, frames/*.vtu

The inputs follow the fields of the Radioss Reference Guide for the input version 2022 (/BEGIN, /NODE, /BRICK, /TETRA4, /TETRA10, /PART, /PROP/SOLID, /MAT/LAW1, /MAT/LAW2, /MAT/LAW36, /FUNCT, /GRNOD, /BCS, /IMPVEL, /INIVEL, /RWALL, /SURF/PART/EXT, /INTER/TYPE24, /TH/NODE, /TH/PART, /TH/RWALL; /RUN, /TFILE, /ANIM, /DT/NODA/CST); the forces of the faces come from the reactions of their nodes in the time history (th_to_csv) or in the animations (anim_to_vtk), the forces on a rigid wall from the change of the momentum.